03-24
2020year
Combustion Synthesis of MgSiN 2 Powder at Different Nitrogen

ABSTRACT. MgSiN 2 powders have been synthesized by combustion synthesis (CS) using Mg and Si 3 N 4 as starting materials at different nitrogen pressures. The CSed powders were then sintered by spark plasma sintering (SPS) to obtain dense bulk MgSiN 2 product.

03-24
2020year
ARCI - Processing

This multi-purpose furnace has wide range of options to carry out heat treatment, powder sintering and annealing under high (10^-6 torr) vacuum and up to 1-3 psig positive pressure of argon, nitrogen or hydrogen atmosphere. The system can be operated at high temperature up to 2000 degree C.

03-24
2020year
High Temperature Electric Plasma Furnace

high speed sintering spark plasma sintering furnace. During the cooling, the SPS furnace was flooded with argon gas to 4 kPa at rate of 10 l/min, maintaining the sintering temperature. It was then quenched from 850°C with room temperature nitrogen gas at a very high flow rate of 8000 l/min from the nozzles.

03-24
2020year
SPARK PLASMA SINTERING AND STRUCTURAL PROPERTIES OF ZrB BASED

part for fabrication of most advanced SPS furnace with bigger sizes (up to 300 mm diameter); see Table 1. This production capacity of a SPS unit is not only ruled by the high heating rate and shorter soak-ing but also by a faster cooling set-up which per-mits quick cooling into the sintering chamber and zone. 3. SPARK PLASMA SINTERING OF ZrB 2

03-24
2020year
spark plasma sintering furnace, spark plasma sintering

Alibaba.com offers 182 spark plasma sintering furnace products. About 60% of these are industrial furnace, 25% are laboratory heating equipments, and 1% are other dental equipments. A wide variety of spark plasma sintering furnace options are available to you, There are 182 spark plasma sintering furnace suppliers, mainly located in Asia.

03-24
2020year
RESEARCH PAPER Comprehensive study of tellurium based glass

spark plasma sintering. These glass ceramic samples exhibited a much better thermoelectric performance. Glass ceramics with 50 mol. % of Bi 0.5Sb 1.5Te 3 show a maximum ZT value equal to 0.37 at 413 K. Meanwhile, the advantages of glass including low sintering temperature and high formability are well maintained.

03-24
2020year
(PDF) Advances in Sintering Science and Technology | Rajendra

Advances in Sintering Science and Technology Ceramic Transactions, Volume 209 A Collection of Papers Presented at the International Conference on Sintering November 16-20, 2009 La Mia, California Edited by Rajendra K. Bordia Eugene A. Olevsky )WILEY A John Wiley & Sons, Inc., Publication This Page Intentionally Left Blank Advances in Sintering Science and Technology This Page Intentionally

03-24
2020year
Metafin Supply Co. - Industrial Interface

Metal Finishing and Electroplating Equipment and Supplies, Metafin Supply Company has been distributing equipment and supplies for the industries for over 30 years. We are located

03-24
2020year
Diamond Archives - Materials Research Forum

Fuji Electronic Industrial Co., Ltd. has taken the initiative in researches and developments of SPARK PLASMA SINTERING (SPS), PECS (Pulsed Electric Current Sintering), technology and fabricating system for leading edge High Density processing.Our results of the developments are shown widely in sintered applications for Functionally Graded

03-24
2020year
Influence of Doping and Nanostructuration on n-Type Bi 2 (Te

Jan 17, 2017 · In competitive thermoelectric devices for energy conversion and generation, high-efficiency materials of both n-type and p-type are required. For this, Bi 2 Te 3-based alloys have the best thermoelectric properties in room temperature applications.

03-24
2020year
FCT Systeme GmbH

High-temperature vacuum sintering furnace. Spark plasma sintering furnace for field assisted sintering technique - „FAST" FCT Systeme GmbH.

03-24
2020year
Nanoscale Texturing and Interfaces in Compositionally

Alternative methods, such as hot pressing and spark plasma sintering (SPS), have also been used to synthesize high-density unmodified and doped Ca 3 Co 4 O 9. The substitution of heavier and smaller Lu 3+ ions on Ca sites has been shown to provide a ZT value of 0.36 at 800 °C through modification of NaCl-type [Ca 2 CoO 3] layer of Ca 3 Co 4 O 9.

03-24
2020year
SPS discharge plasma sintering furnace

SPS is the abbreviation of Spark Plasma Sintering and is used for spark plasma sintering.· Spark plasma sintering (SPS) is a fast, low-temperature, energy-saving and environmentally friendly material preparation technology. 1. Development of spark plasma sintering furnace With the development of high-tech industry, the variety and demand of

03-24
2020year
Spark Plasma Sintering Furnace With High Temperature

Spark plasma sintering (SPS), also known as field assisted sintering technique (FAST) or pulsed electric current sintering (PECS), is a sintering technique. The main characteristic of SPS is that the pulsed or unpulsed DC or AC current directly passes through the graphite die, as well as the powder compact, in case of conductive samples

03-24
2020year
CORE

Spark Plasma Sinteringud (SPS) processes are presented as novel, simple and rapid techniques for the encapsulation of radioisotopic materials within tungsten ceramic-metallic or cermet matrices.

03-24
2020year
Spark Plasma Sintering - IIT Kanpur

Spark Plasma Sintering Sintering is the process of making objects from powder, by heating the material in a furnace below its melting point so that bonding takes place by diffusion of atoms. This leads to individual powder particles adhering to each other in a dense compact. The process is usually used for ceramics.

03-24
2020year
Spark plasma sintering of alumina nanopowders produced by

In the present work, alumina nanopowders produced by electrical explosion of alumina wires were used in the experiments of spark plasma sintering. The SPS graphite die with the sample configuration are shown in Fig. 6. The temperature was measured by an optical pyrometer focused on the surface of the graphite die and automatically regulated

03-24
2020year
Spark Plasma Sintering of Intermetallics and Metal Matrix

Spark Plasma Sintering of Intermetallics and Metal Matrix Composites J. Schmidt, T. Weissgaerber, T. Schubert, B. Kieback Fraunhofer-Institute for Manufacturing and Advanced Materials Dresden Winterbergstraße 28, 01277 Dresden, Germany Abstract Spark Plasma Sintering (SPS) or Field Assisted Sintering (FAST) is a new and innovative

03-24
2020year
Spark Plasma Sintering - YouTube

Sep 04, 2013 · Methology of Spark Plasma Sintering - A detailed procedure.

03-24
2020year
High Temperature Electric Mini Sps Spark Plasma Sintering

High temperature Electric mini sps spark plasma sintering furnace is widely used in ceramics, metallurgy, electronics, glass, chemical, mechanical, refractories, the development of new materials, special materials and building materials production and experiment.